12/31/2023 0 Comments Drumdial drum tuner chartOrdinarily most drums will be tuned to about 75 for the top head and 74 for the bottom resonant head (snare drums tighter, top 85, bottom 82 and bass drums a little looser at 70 to 72). This is not necessary when tightening a tuning lug. When loosening a tuning lug, be sure to pick the dial up and place it down again to relieve pressure on the head, this will assure a correct gage reading. This should not be a problem unless the drum head is extremely worn. However, used heads with indentations and scuffed areas around the edges will make the tuner have different readings if the tuning tip is placed directly on a scuffed surface or in a dent. Picking up the tuner and placing it down again in the same spot should give you an identical gage reading. Now, if you want a different tone, slowly tighten or loosen each tuning lug to your desired tuning point, again matching all gage readings. (Tighten each tuning lug a little at a time, otherwise the drum head will not seat properly.)Ģ. Continue picking up and moving the DrumDial to each tuning point, tightening each tuning lug to achieve identical gage readings. Do this until the drum head is sufficiently tight and the head is properly seated.ģ. At this point, the drum should be in tune with itself. Find the lug with the highest reading and tune the other lugs to match this one. Pick the tuner up and move it to the next tuning lug, and so on (be sure to compress the tuning tip slowly). Take readings using the large needle hand only, the small needle is not used for tuning. At this point, remove your hand from the DrumDial (don’t rest your hand on the drum head as this may give an inaccurate reading). Simply clip it onto the neck of the DrumDial and position the tuner so the Edge Gage lightly touches the inside rim of the drum. This distance can be easily measured using the DrumDial Edge Gage. The DrumDial base should be about ¾ of an inch from the edge of the drum directly in front of a tuning lug. Place the tuning tip on the drum head, always compressing it slowly, until the full weight of the tuner is on the drum. The top cap screw is not used for calibration and should be kept tight and never removed.Position the tuner so the dial is easy to read. Tuning becomes very smooth and drum head skipping or jumping at the hoop edge goes away.1. Make sure that the tuning tip is finger tight. ![]() The cracking sound you are hearing after the head is seated is the drum head collar catching on the bearing edge.Īpply light pressure to the center of a drum without the bearing edge conditioner and listen for the cracking of the drum head as the head collar catches on the bearing edge. The conditioner stick will form a nice groove to take the shape of the top bearing edge, excess force is not required. Epoxy crackling is normal at the Initial seating of the drum head. Excess conditioner to the bearing edge sides is not necessary.Ĥ. Try to keep the conditioner on the top of the bearing edge only, where the drum head comes in contact. Rotate the wheel at the tube bottom to dispense the edge conditioner.ģ. No need to force down on the conditioner stick. Apply the bearing edge conditioner in a smooth non stop application to the entire top bearing edge, rub in excess with your finger tip or wipe off with a dry cloth or paper towel. Wipe down and clean the bearing edge to remove any build up of lint or dust.Ģ. Research, development and product testing over many years, have produced the best bearing edge conditioner available.ĭrumDial Bearing Edge Conditioner will not harm wood, plastics or metal.ġ. DrumDial designed this product specifically for drums. ![]() Made from a proprietary blend of extreme high pressure lubricants and conditioners. Waxes, soaps and petroleum products (ski wax etc.) deaden the drum head and effect the natural sound of the drum. ![]() ![]() It allows the drum head to glide smoothly over the bearing edge without effecting the sound of the drum. This is not a wax, soap or a petroleum product. Solid stick, comes in an easy to use twist tube for a no mess application. Strengthens and conditions the top of the bearing edge where it contacts the drum head. Strengthens and conditions the bearing edge for fast, easy tuning!
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |